Sponsored Links
 

Get Latest Jobs Via Email

Part 2 : We begin to draw (Lesson:13 Trim and Extend)

Part 2 : We begin to draw (Lesson:13 Trim and Extend)autocad

Sponsored Links

“Trim”and “Extend” commands .

We see two other important functions, commands “Trim” and “Extend”.
These commands are on the “modify” toolbar and have the following icons:

trim = Trim.
extend = Extend

Let’s see how to put them into practice.
With the command line, draw five segments, like those in the following figure.

estendi

Extend

Now click on the command “extend”  extend .
On the command line is written “select objects” and the cross-hairs is changed to a selection handle.
Click on the right vertical line on the last hour, then click the right mouse button to confirm your selection.
The command line now asks “Select object to extend. …” , click on the two horizontal lines above, first one then the other, both will be extended until it meets the vertical line that we had selected.
At this point by clicking with the right ends and exits the command.

estendi

In practice at the beginning of the command autocad asks us what objects (lines or shapes), we want to extend one or more lines, and once chosen, we choose to extend the lines on them.
The condition for this is that the lines if projected going to meet the first selected.

In ‘fact, in previous image, the horizontal line at the bottom can not be extended because it would not meet the first line we have chosen as a target.
Be careful because this is a situation that happens often, and drawing in which the neophyte Autocad drawers crashes.
It’s actually very easy to get out, just draw a temporary line, on which we will extend the first vertical line, so on this then, we can extend the horizontal line that was previously not possible to extend.

estendi

In doing so, however, we have extended the vertical line that maybe we wanted to remain as before …
We could then draw another piece of line, following the first, on which to extend the line down and then delete it.
We could also copy ( we’ll see after the copy command ) the vertical line above itself, extend this last line on a provisional basis, as in the image above and then delete them.

In fact, if we have two overlapping lines, and we do click on it to extend, it extends one, the other remains hidden below.
If instead of direct single-click we select through a selection window, then extend both overlapping lines.

Trim

To use ‘Trim’ command the procedure is similar to the previous one:

Continuing from where we are with the extend command, click on the ‘Trim’ command trim, select the vertical line on the left, right button to confirm, then click on the horizontal lines on the left of the vertical, the two lines will be cut from the first, now right-click to finish.
Yet ..
Press return or the right mouse button to resume the command “Trim” select now the two horizontal lines and also the right vertical, as cutting lines (try instead to make a selection window that intersects all) key right, select the four segments to be cut so going to form a rectangle.

Even for the “Trim” then you must select the first cutting objects (lines or shapes) and then the lines or geometric shapes to be cut.
In this case it is obvious how these lines should already be intersected with each other because the former can cut the second.

For both of these two commands you can shorten some steps:
Once you click on control, cut or extend, after pressing the right mouse button or the enter key, it means that all lines could be extended or cut each other, depending on the selected command.

For example:

Draw three vertical lines (they can also be non-parallel) and three horizontal lines that intersect only one of the vertical. (See picture).

taglia

Now click on the “extend”command and then the right mouse button, now click on the horizontal lines several times, they will extend the first line on the first meet and then on the second. In doing so pay attention to the fact that if you click on the part left of these lines by their centers do not extend.
It may seem that the command does not work, but it is not.

If you were to extend a line to the left of course the opposite is true.

Now using the “trim” in the same way that tries to go back to cut the lines that have previously extended, (also try, in addition to select one at a time, to make a box selection that intersects two or three, the latest versions of AutoCAD can be cut or extended in this way many lines in one pass only).

As you can see in this way is like chosen to cut or to extend all the lines in a single click.

Share This Job !
Share On Facebook
Share On Twitter
Share On Google Plus
Share On Linkedin
Share On Pinterest
Share On Reddit
Share On Stumbleupon
Contact us


Get Latest Jobs Via Email

Submit Your Cv
submitCv

Close